Send Message
Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.
Fusion splicer FST-Q5 is not only light, but also good in performance.
FST-Q5 is a new fusion splicer developed by Guangdong Tumtec. The performance is no different from the same level fusion splicer, but it is smaller and lighter than the traditional optical fusion splicer. FST-Q5 appearance The shape is more like a slightly enlarged pos machine, with rubber bumper,the width and height of 132mm/205mm/98mm. Because it’s a hand-held fusion splicer, the requirements for drop resistance are higher, so the four corners are specially strengthened to prevent the...
Fusion splicer is mainly used in the construction and maintenance of optical fiber communication lines. The principle is to generate high voltage arc from the two electrodes to melt the two optical fibers. In addition, a pair of fiber holder equipped with high precision motor is used to gently push the two optical fibers to complete the coupling of optical fiber. According to the working principle, the optical fiber alignment is the most critical factor of the fusion quality, which determines...
Tumtec clad to clad fusion splicer FST-18S, the best at its same level
Welcome to the introduction of Tumtec 4 motors active v-groove cladding Fusion Splicer FST-18S. Combined with novel design, craftsman-level manufacturing technique, it updates to high-precision algorithm to reach the fast splicing 5s, fast heating 13S for multiple fiber types: SM/MM/DS/NZDS.. Fast heating 13s, its been preset with 5 kinds of heating modes (20mm/30mm/40mm/50mm/60mm); Users can adjust the heating modes according to their applicable scenarios and habits, 50 kinds heating modes can...
Choose High Precision Fusion Splicer to Increase Splice Quality and Efficiency
With the widespread application of optical fiber in modern communication and broadband interconnection network and the wide application of optical fiber communication technology, optical fiber fusion splicer has become an indispensable instrument in optical network construction and daily maintenance. It is used in the maintenance and fusion of optical fiber layout. In order to obtain high quality spliced fiber during fusion, high precision alignment of optical fiber core is required. The...
The Usage of Multi Functional Fiber Holder
Fusion splicer is equipped with multi functional fiber holder, which will be convenient for splice, no need to change fiber holder frequently and increase efficiency. With the upgrade of fusion splicer, Tumtec fiber holders are multifunctional and suitable for various kinds of fibers like bare fiber, pigtail, drop cable etc. Tumtec fiber holder can support different diameters of drop cable and pigtail location, can make splice directly. For multifunctional fiber holder, we shall control well...
Go forward with heart, Tumtec will fly in 2021, and create great achievements
On January 8, 2021 Guangdong Tumtec Communication Technology Co., Ltd. held an annual meeting to summarize the operation of the year and look forward to a bright future. Looking back on 2020, because of the epidemic, many things are forced to press the pause button, disrupting the original rhythm. In the face of this sudden change, Tumtec technology also adjusted its strategy and company development plan in time, strengthened its belief in adversity, seeks development in adversity, seized...
Why do we need to do ARC adjust operation?
Have you ever been troubled by the continuous decline of its parameters, Optical Fiber Fusion Splicer quality and the inability to determine the appropriate ARC value when splicing? 01 Why do discharge calibration Atmosphere like temperature, humidity, air pressure are always changing. This makes the discharging temperature change as well. The machine is equipped with temperature and air pressure sensor which can give feedback to the control system to adjust the discharge intensity to maintain...
The Cause for Fiber Imaging Become Blurring during Fusion
In winter, the weather is cold, and the temperature difference between indoor and outdoor is big, especially in the northern region with the heating system on, the temperature difference is much bigger, and condensate water is easy to be generated. Fusion splicer will also be affected by the change of weather environment. Light sensor at low temperature will frozen and condensed water or water mist will be generated on the lens surface. During fusion, the optical fiber imaging will be blurred,...
Do you know the importance of electrode replacement？
Electrode rod is an important part in splicing machine. Discharge splicing is completed by electrode rod. However, many people do not know that electrode rod is a consumable material.It needs to be replaced when it reaches a certain life span. I will introduce you to the importance of electrode rod exchange and some knowledge related to the life span. First to know about the electrode stick aging process, the electrode stick with the naked eye observation is similar to the very tip of a needle,...
Tumtec participation in 2020 “ The Wuhan OVC Expo“
The Wuhan OVC Expo is a large-scale and influential annual grand event for the Optoelectronic industry, covering hot topics such as optical communications, 5G communications, precision optics, photoelectric sensors, new materials, etc. It is an excellent platform for many optoelectronic companies for expand market, promote brand and display new product. Also it is a professional platform for people working in the optoelectronic industry to find new technologies and products, to understand...
The advantages of Fusion Splicer FST-18S
Tumtec fusion splicer FST-18S is with red casing. It is Moistureproof, frost proof, dust proof, and shock proof. When taking fuson splicer FST-18S outside for work, it can draw attention for its red casing. Appearance, color and design are not so important for the fusion splicer. What the communication staff concerns about is the splice loss and stability. In respect to this point, we made a video for the loss of Optical Splicer FST-18S. The video is as below: From the video, the loss tested...
Solutions to “fiber tracking failed”
Machine shows “fiber tracking failed” when splicing. There are multiple reasons for this: Abnormal fiber holder guiding Dust on camera Fiber is not pressed properly; CMOS malfunction Dirty CMOS board Here we gonna introduce the solutions for fiber holder pushing abnormality; When the machines splicing and shows ‘fiber tracking failed’, open up the shield cover, and observe the trajectory of the fiber holder We can see the right fiber holder is normal, and left fiber...
【Video Collection】Various kind of Tumtec Fusion Splicer Available
Tumtec fusion splicer with various kinds of model, covering for backbone, MAN, FTTX Telecom, meet different market demands. Tumtec fusion splcier high-end configuration/advantages The fusion splicer adopts newly design and advanced manufacturing technology, Micron level parallel clamping, precise alignment and advanced profile direct vision technique to make sure the accuracy of estimated splice loss Fast Operation 3s to turn on, 6s to splice, 15s to heat, the fusion splicer can automatically...
2020 Tumtec Technology Appreciation Dinner was successfully held
I am grateful to be with you all the way to thank all customers and colleagues for their support to Tumtec. On the evening of September 9, 2020, the "2020 Tumtec Technology Appreciation Dinner" hosted by Guangdong Tumtec Communication Technology Co., Ltd. was grandly held in the Chopin Hall of Vienna Hotel, Bao'an District, Shenzhen. We invited many leaders and guests to this dinner, thanks for your continued support and help to Tumtec Technology! At the party, we brought delicious food,...
Reason and solution of “Fiber tracking failure”
When splicing the fiber, will you meet the fiber tracking failure? There are several reasons caused the failure: Dust on lens Pressure hammer not working precisely on pressing the fiber CMOS board malfunction Dust on CMOS BOARD How to solve the problem? Firstly, lets check if V-Groove is clean or not? The pressure hammer tip point is not on the V-Groove and not pressed on fiber Under normal circumstances, tip point of pressure hammer should be exactly on the central point of V-groove and press...
CFCF2020｜Tumtec Communication was selected as
The 2020 Optical Connection Conference is an annual optical communication industry event focused on optical fiber online. The conference is based on the core characteristics of seamless beam connection, perfectly fits the development core of "new infrastructure", and focuses on the construction and development of optical networks in the 5G and cloud era. With the theme of "Fitlink, a colorful future", looking for new markets, new technologies and new opportunities for optical communications in...
Welcome to view Tumtec factory through VR 360-degree cloud visit!
Regarding Tumtec, you may hear and see different comment or evaluation. So, what is Tumtec really like under the camera? Good working environment and corporate culture of a company can reflect the overall strength of a company. Therefore, we have developed a VR panoramic view so that customers can learn more about Tumtec online. Come closer and look Lets take you 360° cloud tour in Tumtec factory Swipe to view VR panorama Stepping into Tumtec It is also trying to tell its 16-year history and...
Conform to the development needs of the times,and adapt to market demand
In the Internet age, across time and space, people can know current events around the world and exchange information without leaving their homes. Now that technology has developed to the point where they can use the Internet to experience everything in the world, such as AI Technology, 5G technology. The development of science and technology is inseparable from many equipment support, such as the optical fiber fusion splicer commonly used in the construction of communication systems. Optical...
Tumtec fiber fusion machine daily delivery
Clunk, this morning another container shipment ~ Just arrived at the downstairs of the company this morning, I saw that the container loaded by Our Tengyou company was waiting at the downstairs of the factory early (I had to praise the dedication of the container driver), waiting for tengyou staff to melt the receiver and load it down. Since the establishment of the company, Tengyou has been actively exploring the national and global markets, which is also due to years of pursuit of product...
The latest breakthrough | Tumtec released ribbon fusion splicer
The new product -- Tumtec FST-12R ribbon fiber fusion splicer, is the latest research and development, inherits the advantages of the Tumtec classic fiber splicer, and greatly improves the performance, combined with the advanced technology at home and abroad, to optimize the product performance, appearance and improve the user experience, comparable to imported high-end models. Tumtec never stop on the road of innovation, has been pursuing higher quality, serve for customers.During the research...
The Usage and Maintenance of Fusion Splicer Battery(two)
Generally lithium batteries can be recharged/discharge 300 to 500 times.It is better to discharge the lithium battery partially rather than completely, and to avoid frequent full discharge as much as possible. The life of a lithium battery lies in its first few years, whether you use it or not.The decrease in battery capacity is due to an increase in internal resistance due to oxidation (which is the main cause of the decrease in battery capacity).Finally, the cell resistance reaches a point at...
Another shipment for tender, Tumtec won the bid for the Asian market project
First of all, we are thankful for customers’ support and trust during the pandemic period,Then thanks to the employees for working together to complete the mass production and shipment. This Asian project is in high demand. Tumtec company management has arranged this order in logical sequence, the staff cooperated to ensure the product quality and batches of shipments. Let us have a look at the shipment! Mr. Yu, the general manager of Tumtec said that we must complete the supply on time,...
The Usage and Maintenance of Fusion Splicer Battery（one)
In general, the new lithium battery of the fusion splicer is empty when delivered from factory. It is recommended to charge it first and then use it. The battery of fusion splicer needs to be charged and used for three to four times to reach the best condition. Many friends meet small problems about charging like the discharging times of ARC is not as many as imagination. After 3-5 times of charging and use, they are all solved. Charged in long time But some people ask, is it true that the...
Congrats to our Tumtec team on winning the tender from Asia market
Tumtec won the Asian market project Congrats to our Tumtec team on winning the tender from Asia market. After a period of close production, part of the goods preparation has been completed. Let's take a look at the whole process of goods preparation and shipment. Tumtec Stock up TumtecStock up Tumtec Stock up Tumtec Stock up Tumtec Stock up Tumtec Stock up container shipment Tumtec container shipment tumtec container shipment tumtec iness container shipment tumtec container shipment tumtec...
Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.
Fill in more information so that we can get in touch with you faster
Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.